Top Tips for preparing your home for a new floor installation

Top Tips for preparing your home for a new floor installation
laminate flooring - worker installing new floor

Before installing a new floor in your home, it is essential to prepare the area for it. It includes removing any baseboards, door frames, and base shoe moldings. Additionally, it would help if you disconnected any gas appliances and electronics. Doors may need to be adjusted as well. To allow new flooring installation, a wall base should be approximately three-eighths of an inch off the floor.

Remove base shoe moldings

Base shoe moldings are small strips of wood that fit in the corner of a room’s floorboard. They are usually painted to match the trim and are installed at the appropriate angle. While baseboards are generally straight, floor coverings are only sometimes. Older homes often have sags between the joists and floor coverings. Even newer homes can have uneven floor surfaces.

Quarter-round moldings and shoe moldings are also flexible. They are meant to bend to fit the floorboard profile and give the new floor more room to expand. During installation, you can use a nail gun to nail the shoe molding to the baseboard. It will ensure that the trim fits appropriately, and you can easily access it from underneath. The best nail gun for this job is an electric brad nailer, which automatically sets small finish nails and speeds up your work.

Remove baseboards

Removing baseboards is essential in preparing your home for a new floor installation. They must be removed when installing new flooring, ripping out the old floor, or painting or resurfacing the walls. When you remove baseboards, you should reuse them whenever possible. These boards can be reused for other purposes, including painting or refinishing walls. Furthermore, wood products and lumber are becoming more expensive, so it makes sense to reuse them if possible.

To remove baseboards, start at the outside corner of the room. It is because baseboards are sometimes installed with a mitered joint, making it difficult to pry them from an interior corner. The outside corner provides better access and lets you slide a putty knife behind the molding. Once the baseboard is in the open, use a wooden block to push it down the length of the wall.

When you remove baseboards, you should consider the type of flooring you are installing. The baseboard is a barrier between the floor and the drywall. It also protects the drywall from moisture, which can expand. You can decide to paint or stain the baseboard if you want. You should also consider the cost of replacing the baseboard if it is cracked or damaged. If the baseboard is damaged, it might not fit properly when replaced.

Remove door frames

Removing door frames will make installing a new floor faster and easier than removing individual flooring pieces. In most cases, removing a door frame and replacing it with the new one is easy. However, there may be times when a modification is needed to the door frame, which will require extra work. If this is the case, you must purchase a jamb saw.

Before you begin removing door frames, you must first remove the doors. When removing door frames, measure the area and use a tool with high-speed settings. Place the tool on the floor next to the door frame. The blade of the device should be adjusted to fit in the channel. Then, use the tool to cut the frame. Make sure to read the markings on the tool’s blade to know how deep you need to cut. After cutting, you must be careful not to cut deeper than the door jamb.

If you have a rotted wood door frame, it’s time to replace it. While it may seem easy, this process can be expensive. The cost varies greatly depending on the door frame style, location, and material. Softwood frames are the cheapest and easiest to work with. Sometimes, it’s easier to hire a door repair company to replace the frames.

Subfloor prep requirements

Sub-floor preparation is critical for any flooring project. Mistakes made in this step can lead to problems years down the road, so it’s essential to understand the proper floor prep process. Most manufacturers recommend using a concrete grinder, bead blaster, or sandpaper to prepare the subfloor. However, beware of chemical removers, as they can soak into the concrete and cause problems with the bond.

Preparing the subfloor is one of the most critical steps to maximize the benefits of your new floor. By cleaning and leveling your subfloor, you will ensure the integrity of your new floor and avoid unwanted sounds, smells, and sagging. The correct subfloor preparation can provide a seamless installation process. If you want to make sure your floor will last for years, this is an important step.

The subfloor must be clean, flat, and structurally sound if you use wood flooring. It should be free of squeaks and protruding fasteners. In addition, it must be flat and free of peaks or valleys. If the subfloor is uneven, it must be sanded and filled with a leveling compound specifically designed for wood flooring.